MATHS WITH MATT · A-LEVEL PHYSICS

Photoelectric Effect Simulation

Use this free photoelectric effect simulation to explore photons, stopping potential and electron speeds. Compare classical predictions with observations and measure Planck’s constant.

How to use this photoelectric effect simulation

This free photoelectric effect simulation helps A-Level Physics students connect photons, electron emission and experimental evidence. Choose a metal, change the light frequency and adjust its intensity. Watch photons arrive across the surface, then compare the energy and speed of emitted electrons. Use the controls beside the model and pause whenever you want to inspect the motion.

Threshold frequency, work function and electron energy

Start with Photons & metal. Each photon carries energy hf, where h is Planck’s constant and f is frequency. The work function φ is the minimum energy needed to remove an electron from the surface. Below the threshold frequency f₀ = φ/h, no electrons escape in this single-photon model. Brighter light cannot overcome that energy deficit.

Above threshold, the maximum kinetic energy is KEmax = hf − φ. Other electrons can emerge with less energy because of their initial states and energy transfer inside the metal. Compare the illustrative energy histogram with the maximum-energy example. The worked speed calculation uses KEmax = ½mvmax², with energy converted from electronvolts to joules.

Stopping potential in a vacuum photocell

Next, select Vacuum photocell. Light enters through the window and illuminates the emitting face of the photocathode. A positive anode bias accelerates electrons across the evacuated gap. A negative bias retards them, so slower electrons turn back before reaching the anode. Follow the highlighted fastest electron to see its kinetic energy and speed change.

At the stopping potential, the retarding energy equals the maximum initial kinetic energy: eVₛ = KEmax. Here Vₛ is a positive magnitude; the anode is at −Vₛ relative to the photocathode. The energy bars show this balance. Increasing intensity raises the saturation current at fixed frequency, while the stopping potential stays the same.

Classical predictions versus observations

The comparison tab tests three important observations. First, there is a threshold frequency regardless of intensity. Second, a suitable photon can release an electron without an energy-accumulation delay. Third, brighter light increases the emission rate rather than the maximum electron energy. Compare these results with a simple classical continuous-energy explanation, then use the photon model to explain each difference.

The single-photon demonstration separates travel to the surface from absorption and emission. Its slowed flight is a drawing convention, not an experimental emission delay. At low intensity, a site can wait for a photon to arrive. However, the electron does not need to store energy from several sub-threshold photons before escaping.

Measure Planck’s constant with the photoelectric effect simulation

Use Measure Planck’s constant to record stopping potentials at three or more frequencies above threshold. Keep the metal fixed and find the smallest retarding voltage that just stops the photocurrent. Record each reading, then change frequency. The graph fits Vₛ against f. Its gradient is h/e, so multiplying the gradient in V Hz⁻¹ by the elementary charge gives h in J s.

The vertical intercept gives −φ/e and the horizontal intercept gives f₀. Repeat with another metal to compare thresholds and work functions. Both lines should have the same gradient. You can edit or remove readings and add a labelled ideal reference series. These are simulated measurements based on the model, rather than independent evidence for the value of h.

Zinc electroscope and model assumptions

Finally, charge the electroscope negatively and select short-wave UV. Emitted electrons escape, reducing the negative charge as the gold leaf falls. Visible light below threshold does not produce this discharge. Insert ordinary glass to block the model’s short-wave UV. A strongly positive plate attracts low-energy emitted electrons back and does not gain the electrons needed to neutralise its charge.

The photoelectric effect simulation uses representative, surface-dependent work functions and a simplified energy distribution. It assumes ideal parallel electrodes, fixed quantum yield and no leakage or air ionisation. Motion is magnified and slowed; photon packets and electron markers represent the underlying flow. UV and infrared are shown using false colours for visibility.

Explore more free physics simulations, including the Bohr model, or practise with A-Level Physics questions by topic. Maths With Matt provides free resources and online Maths and Physics tuition for students across the UK.

Further reading: OpenStax: the photoelectric effect and the Institute of Physics electroscope demonstration.

Share this free photoelectric effect simulation: WhatsApp · Email.